Cisco 200-105 Exam Dumps

      Comments Off on Cisco 200-105 Exam Dumps

The major reason of our success is valid Cisco 200-105 exam dumps PDF format. This PDF format is user friendly and provides relevant knowledge of Cisco Networking so that you attempt all required questions of the 200-105 exam.

Try it Latest DumpsSchool 200-105 Exam dumps. Buy Full File here: https://www.dumpsschool.com/200-105-exam-dumps.html (691 As Dumps)

Download the DumpsSchool 200-105 braindumps from Google Drive: https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view (FREE VERSION!!!)

Question No. 1

Which three features are added in SNMPv3 over SNMPv2? (Choose three.)

Answer: A, C, D

Question No. 2

Which value must you configure on a device before EIGRP for IPv6 can start running?

Answer: C

Question No. 4

What is the alternative notation for the IPv6 address B514:82C3:0000:0000:0029:EC7A:0000:EC72?

Answer: D

Question No. 5

If two OSPF neighbors have formed complete adjacency and are exchanging link-state advertisements, which

state have they reached?

Answer: C

Question No. 6

Refer to the exhibit. A junior network engineer has prepared the exhibited configuration file.

What two statements are true of the planned configuration for interface fa0/1? (Choose two.)

Answer: B, E

Question No. 7

Which three statements are benefits of using a shadow router as the source of IP SLA measurements?

(Choose three.)

Answer: A, B, D

A dedicated router used as a source of IP SLA measurement is also called a shadow router. Implementing IP

SLA with a shadow router has several advantages:

* Dedicated router would offset the resource load on production router from the implemented IP SLA Network

Management operations

* Dedicated router would be a central device that can be independently managed without any impact on

network traffic.

* Granting SNMP read-write access to the device might not be such a huge security risk compared to enabling

SNMP read-write on a production router carrying customer traffic.

* Better estimation of Layer 2 switching performance can be obtained if the access port is placed on the same

switch/linecard as the endpoint to be managed. This is because the IP SLA packets also have to traverse the

same interface queuing at the access layer as the regular IP packets.

https://www.cisco.com/en/US/technologies/tk869/tk769/

technologies_white_paper0900aecd806bfb52.html

Question No. 8

Which function is performed by a TACACS+ server?

Answer: B

Question No. 9

Which command must you enter to enable OSPFV2 in an IPV4 network?

Answer: D

Question No. 10

In which solution is a router ACL used?

Answer: A

Question No. 11

What are the two default metrics used by EIGRP for route selection? (Choose two.)

Answer: A, B

EIGRP adds together weighted values of different network link characteristics in order to calculate a metric for evaluating path selection.

These characteristics include:

* Delay (measured in 10s of microseconds)

* Bandwidth (measured in kilobytes per second)

* Reliability (in numbers ranging from 1 to 255; 255 being the most reliable)

* Load (in numbers ranging from 1 to 255; 255 being saturated)

Various constants (K1through K5) are able to be set by a user to produce varying routing behaviors. However by default, only delay and bandwidth are used in the weighted formula to produce a single 32bit metric:

Note:Default K values are:K1=K3= 1 andK2=K4=K5= 0

When K5is equal to 0 then [K5/(K4+ reliability)] is defined to be 1

Use of the default constants effectively reduces the formula above to:

http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/enhanced-interior-gateway-routing-protocol-eigrp/whitepaper_C11-720525.html

Question No. 12

Instructions

Why is the Branch2 network 10.1 0.20.0/24 unable to communicate with the Server farm1 network 10.1 0.10.0/24 over the GRE tunnel?

Answer: C

Question No. 13

Refer to the exhibit.

Assume that all of the router interfaces are operational and configured correctly. How will router R2 be affected by the configuration of R1 that is shown in the exhibit?

Answer: A

Open Shortest Path First

http://en.wikipedia.org/wiki/Open_Shortest_Path_First

The configuration of R1 shows “router ospf 1” however, the diagram also shows that both routers should be in the backbone OSPF Area of “0”. When routers are in different OSPF areas they will not form a neighbor relationship.

Neighbor relationships

As a link state routing protocol, OSPF establishes and maintains neighbor relationships in order to exchange routing updates with other routers. The neighbor relationship table is called an adjacency database in OSPF.

Provided that OSPF is configured correctly, OSPF forms neighbor relationships only with the routers directly connected to it. In order to form a neighbor relationship between two routers, the interfaces used to form the relationship must be in the same area. Generally an interface is only configured in a single area, however you can configure an interface to belong to multiple areas. In the second area, such an interface must be configured as a secondary interface. (A neighbor state simulation shows how neighbor state changes from Down to Full Adjacency progressively with exchanging Hello, DD, Request, Update, and Ack packets).

200-105 Dumps Google Drive: (Limited Version!!!)
https://drive.google.com/file/d/1TwCxP9R2WPXn5O77CUBND73niqczpZDp/view

Related Certification: CCNA Routing & Switching dumps