New FORTINET NSE7 Exam Questions Are Out – (Dec-2017 Dumps)

      Comments Off on New FORTINET NSE7 Exam Questions Are Out – (Dec-2017 Dumps)

Fortinet Network Security Expert NSE7 exam is a milestone in the industry to endorse your proficiency. Passing FORTINET NSE7 exam entitles you for the achievement of Fortinet Network Security Expert certification exam. We at RealExamDumps provide you latest FORTINET NSE7 exam questions. The candidates those who endorse their proficiency by passing the Fortinet Troubleshooting Professional NSE7 exam get the edge in the industry and get better employment opportunities.

Version: 9.0
Question: 1

Examine the following partial outputs from two routing debug commands; then answer the question below.
# get router info routing-table database
s 0.0.0.0/0 [20/0] via 10.200.2.254, port2, [10/0] s *> 0.0.0.0/0 [10/0] via 10.200.1.254, port1
# get router info routing-table all
s* 0.0.0.0/0 [10/0] via 10.200.1.254, port1
Why the default route using port2 is not displayed in the output of the second command?

A. it has a lower priority than the default route using port1.
B. it has a higher priority than the default route using portl.
C. it has a higher distance than the default route using portl.
D. it is disabled in the FortiGate configuration.

Answer: A

Question: 2

Examine the output of the ‘diagnose ips anomaly list’ command shown in the exhibit; then answer the question below.

Which IP addresses are included in the output of this command?

A. Those whose traffic matches a DoS policy.
B. Those whose traffic matches an IPS sensor
C. Those whose traffic exceeded a threshold of a matching DoS policy.
D. Those whose traffic was detected as an anomaly by an IPS sensor.

Answer: D

Question: 3

New Updated NSE7 Exam Questions NSE7 PDF dumps NSE7 practice exam dumps: https://www.dumpsschool.com/NSE7-exam-dumps.html (45 Questions)

Examine the partial output from the IKE realtime debug shown in the exhibit; then answer the question below.

Why didn’t the tunnel come up?

A. IKE mode configuration is not enabled in the remote IPsec gateway.
B. The remote gateway’s Phase-2 configuration does not match the local gateway’s phase-2 configuration.
C. The remote gateway’s Phase-1 configuration does not match the local gateway’s phase-1 configuration.
D. One IPsec gateway is using main mode, while the other IPsec gateway is using aggressive mode.

Answer: B

Question: 4

Four FortiGate devices configured for OSPF connected to the same broadcast domain. The first unit is elected as the designated router The second unit is elected as the backup designated router Under normal operation, how many OSPF full adjacencies are formed to each of the other two units?

A. 1
B. 2
C. 3
D. 4

Answer: B

Question: 5

The logs in a FSSO collector agent (CA) are showing the following error: failed to connect to registry: PIKA1026 (192.168.12.232) What can be the reason for this error?

A. The CA cannot resolve the name of the workstation.
B. The FortiGate cannot resolve the name of the workstation.
C. The remote registry service is not running in the workstation 192.168.12.232.
D. The CA cannot reach the FortiGate with IP address 192.168.12.232

Answer: C

Question: 6

Examine the output of the ‘get router info ospf interface’ command shown in the exhibit; then answer the question below.

Which statements are true regarding the above output? (Choose two.)

A. The port4 interface is connected to the OSPF backbone area.
B. The local FortiGate has been elected as the OSPF backup designated router
C. There are at least 5 OSPF routers connected to the port4 network.
D. Two OSPF routers are down in the port4 network.

Answer: BD